propeller shaft
英 [prəˈpelə(r) ʃɑːft]
美 [prəˈpelər ʃæft]
网络 传动轴; 驱动轴; 螺旋桨轴; 推进轴; 推进器轴
双语例句
- There must be one or more universal joints to permit variations in the angle of drive. There must also be a slip joint that permits the effective length of the propeller shaft to change.
可轴向移动的球笼式万向节一个或几个万向节来适应传动角度的变化；一套伸缩花键，能够改变传动轴的现有长度。 - These drive the central propeller shaft through bevel reduction gears with a2:1 reduction.
这些驱动器，中央螺旋桨轴通过减少锥齿轮2：1减少。 - When taking propeller shaft joint angle measurements, or checking the phasing, of two piece shafts, consider each shaft separately.
当测量两个传动轴的工作角或检查它们是否定相时，对它们要分别考虑。 - Drive pinion cone bearing propeller shaft pinion flange
传动轴主动齿轮凸缘 - This measurement will give you the propeller shaft angle ( C).
测量结果就是传动轴工作角（c）。 - Nothing seems to be wrong with the propeller shaft.
转动轴看来没毛病。 - In this artide, feasibility analysis of the technology of cold drawing with core mandrel for the propeller shaft tube stock has been made and technological testing carried out.
对加工传动轴管采用的带芯冷拔工艺进行了可行性分析，并进行了工艺试验。 - Install the straps and bolts to hold the propeller shaft to the yoke.
安装扣夹和螺栓，将传动轴固定到轴轭上。 - Inspection machining dimension of propeller shaft ( intermediate shaft or counter shaft).
螺旋桨与轴胶合联结螺旋桨轴（间轴）加工尺寸检查。 - Mark the propeller shaft and pinion yoke, or pinion flange, for installation reference.
在传动轴和传动轴轴轭、或小齿轮轴轭上作标记，作安装的参考标志。 - He's hiding in the propeller shaft.
他躲在传动轴那。 - Align previously made marks on yoke and propeller shaft and install propeller shaft.
将定位轭架上的预制标记对准传动轴并安装传动轴。 - Align the installation reference marks on the propeller shaft and yoke and install the propeller shaft.
对准传动轴和轭上安装参考标记，安装传递轴。 - Discussion on Machining of Propeller Shaft for 230 000 DWT Ore Carrier
230000DWT矿砂船螺旋桨轴加工问题探讨 - Different nacelle with deeper ross-section and intake over propeller shaft.
发动机舱、螺旋桨轴处的进气口有一些不同。 - Propeller shaft pinion flange main drive gear bearing oil slinger
传动轴主动齿轮凸缘主动齿轮轴承抛油环 - Different nacelle with deeper ross-section and intake over propeller shaft. inspection certificate of imported motor vehicles
发动机舱、旋桨轴处的进气口有一些不同。进口机动车辆检验证明 - In this paper the author emphasizes the importance of balancing the rotating parts, such as crankshaft, flywheel, propeller shaft, wheel and tyre, etc. during automobile repair.
分析了汽车维修中曲轴、飞轮、传动轴、车轮、轮胎等旋转零件进行平衡试验的重要性。 - Abnormal noise often occurs in motor vehicle transmission system especially in propeller shaft and final reduction gear.
汽车传动系特别是传动轴与主减速器常产生异常响声。 - Research on the Influence of Ship Propeller Shaft Deformation to the Stiffness Coefficient of Journal Bearing Lubricant Film
船舶螺旋桨轴变形对轴承油膜刚度的影响研究 - Research on Coupling Theory and Its Experiments between Vibration and Lubrication of Ship Propeller Shaft
船舶螺旋桨轴振动与润滑耦合理论和试验研究 - In this article, based on room temperature creep analysis on propeller shaft, a dynamic and a fatigue analysis on the propeller shaft are carried out.
本文针对常温下长期受到恒定载荷作用下的某舰螺旋桨尾轴进行了常温蠕变分析，并对变形后的螺旋桨尾轴进行了动力和疲劳分析。 - The propeller shaft frequency is one of the important target recognition features for passive sonar.
螺旋桨轴频是被动声纳极其重要的目标识别特征之一。 - The Microprocessor Device to Measurements of Torque, Rotational Speed and Power on the Propeller Shaft of Ship
一种用于测量船舶推进轴的转矩、转速和功率的微处理仪器 - In the paper, effective modal mass of the propeller shaft bracket system was studied and calculated.
研究中引入有效模态质量，并计算了尾轴架系统的有效模态质量。 - However, detailed analysis and computer simulation indicate that the first calculation vibration modal was not the first vibration modal of the propeller shaft bracket system.
但是，关于尾轴架系统振型的详细分析与计算机仿真表明，计算所得的第一阶振型并不是尾轴架系统本身的首阶振型。 - Three dimensional numerical simulation of cold extrusion molding process of propeller shaft involute spline of a motor vehicle is carried out with MSC/ Superform software.
采用MSC/Superform软件对某型汽车传动轴渐开线花键冷挤压成形过程进行了三维数值模拟。 - Besides, the nonuniformity of motion of an inclined propeller shaft during steering is also studied.
并分析倾斜布置的传动轴在转向行驶时的运动不均匀性。 - Propeller shaft bracket system of a ship was simulated by beam element model and body element model. Using the large finite element software of Nastran, vibration of the propeller shaft bracket system was calculated based on the two models.
对某舰的尾轴架系统，分别采用梁单元和体单元两种不同的建模方法进行模拟，用大型有限元NASTRAN软件对两种模型进行振动计算。 - It proved that the optimized results meet the strength and stiffness. So it showed that genetic algorithm has high credibility and feasibility on propeller shaft bracket structure optimization.
结果表明，优化结果完全满足强度和刚度要求，说明遗传算法对船舶尾轴架结构的优化具有很高的可信度和可行性。